Ace FCP_FGT_AD-7.6 Certification with 45 Actual Questions
PASS Fortinet FCP_FGT_AD-7.6 EXAM WITH UPDATED DUMPS
NEW QUESTION # 17
Which three statements about SD-WAN performance SLAs are true? (Choose three.)
- A. They rely on session loss and jitter.
- B. All the SLAtargets can be configured.
- C. They monitor the state of the FortiGate device.
- D. They can be measured actively or passively.
- E. They are applied in a SD-WAN rule lowest cost strategy.
Answer: A,B,D
Explanation:
SD-WAN SLAs monitor metrics like packet loss and jitter to evaluate link performance.
SLA measurements can be performed using active probing or passive monitoring.
Administrators can configure all SLA target parameters to define performance criteria.
NEW QUESTION # 18
An administrator notices that some users are unable to establish SSL VPN connections, while others can connect without any issues.
What should the administrator check first?
- A. Ensure that forced tunneling is enabled to reroute all traffic through the SSL VPN
- B. Ensure that the HTTPS service is enabled on SSL VPN tunnel interface
- C. Ensure that the affected users are using the correct port number.
- D. Ensure that user traffic is hitting the firewall policy.
Answer: D
Explanation:
If user traffic is not matching the appropriate firewall policy that permits SSL VPN, users will be unable to establish connections, making this the first aspect to verify.
NEW QUESTION # 19
FortiGate is operating in NAT mode and has two physical interfaces connected to the LAN and DMZ networks respectively.
Which two statements about the requirements of connected physical interfaces on FortiGate are true? (Choose two.)
- A. Both interfaces must have DHCP enabled and interfaces set to LAN and DMZ roles assigned.
- B. Both interfaces must have the interface role assigned.
- C. Both interfaces must have directly connected routes on the routing table.
- D. Both interfaces must have IP addresses assigned.
Answer: C,D
Explanation:
Interfaces must have directly connected routes in the routing table to forward traffic correctly.
Interfaces must have IP addresses assigned to communicate within their respective networks.
NEW QUESTION # 20
Refer to the exhibits.
The exhibits show a diagram of a FortiGate device connected to the network, as well as the IP pool configuration and firewall policy objects.
The WAN (port2) interface has the IP address 100.65.0.101/24.
The LAN (port4) interface has the IP address 10.0.11.254/24.
Which IP address will be used to source NAT (SNAT) the traffic, if the user on HQ-PC-1 (10.0.11.50) pings the IP address of BR-FGT (100.65.1.111)
- A. 100.65.0.99
- B. 100.65.0.149
- C. 100.65.0.49
- D. 100.65.0.101
Answer: A
Explanation:
The ping traffic policy uses the IP pool named SNAT-Remote1, which has the external IP range 100.65.0.99. Therefore, traffic matching this policy (ping from HQ-PC-1 to BR1-FGT) will use 100.65.0.99 for source NAT.
NEW QUESTION # 21
Which two statements describe characteristics of automation stitches? (Choose two.)
- A. An automation stitch can have multiple triggers.
- B. Multiple actions can run in parallel.
- C. Actions involve only devices included in the Security Fabric.
- D. Triggers can involve external connectors.
Answer: B,D
Explanation:
Automation stitches can execute multiple actions concurrently (in parallel).
Triggers for automation stitches can come from external connectors beyond just Fortinet devices.
NEW QUESTION # 22
You have configured the FortiGate device for FSSO. A user is successful in log-in to windows, but their access to the internet is denied.
What should the administrator check first?
- A. The FortiGate FSSO active users list for user's IP address.
- B. The FortiGate firewall policy settings for SSL decryption.
- C. The windows event viewer for failed login attempts.
- D. Whether the user is assigned to the correct AD group.
Answer: A
Explanation:
Checking the active users list verifies if FortiGate correctly associates the user with their IP address, ensuring proper policy enforcement for internet access.
NEW QUESTION # 23
An administrator wants to analyze and manage digital certificates to prevent browser warnings when users connect to the SSL VPN portal.
Which two statements describe how to correctly do this? (Choose two.)
- A. The administrator can use a publicly trusted certificate from a known certificate authority (CA) to stop browser warnings.
- B. The administrator must disable HTTPS administrative access entirely to avoid certificate warnings.
- C. The administrator can import the FortiGate self-signed certificate into each user's browser as a trusted certificate.
- D. The administrator can rely on the default FortiGate self-signed certificate to prevent all security warnings in the browser.
Answer: A,C
Explanation:
Using a publicly trusted certificate from a known CA prevents browser warnings without additional user action.
Importing the FortiGate self-signed certificate into users' browsers as trusted eliminates warnings caused by untrusted certificates.
NEW QUESTION # 24
Refer to the exhibit, which shows an SD-WAN zone configuration on the FortiGate GUI.
Based on the exhibit, which statement is true?
- A. The Underlay zone is the zone by default.
- B. port2 and port3 are not assigned to a zone.
- C. The Underlay zone contains no member.
- D. The virtual-wan-link and overlay zones can be deleted.
Answer: A
Explanation:
The Underlay zone is the default SD-WAN zone, typically representing the physical interfaces in the SD-WAN configuration before overlay or virtual links are added.
NEW QUESTION # 25
Refer to the exhibit.
What would be the impact of these settings on the Server certificate SNI check configuration on FortiGate?
- A. FortiGate will accept the connection with a warning if the SNI does not match the CN or SAN fields.
- B. FortiGate will close the connection if the SNI does not match the CN and SAN fields
- C. FortiGate will accept and use the CN in the server certificate for URL filtering if the SNI does not match the CN or SAN fields.
- D. FortiGate will close the connection if the SNI does not match the CN or SAN fields.
Answer: B
Explanation:
With the Server certificate SNI check set to Strict, FortiGate enforces that the SNI must match either the Common Name (CN) or Subject Alternative Name (SAN) in the server certificate; otherwise, it closes the connection.
NEW QUESTION # 26
What is the primary FortiGate election process when the HA override setting is enabled?
- A. Connected monitored ports > System uptime > Priority > FortiGate serial number
- B. Connected monitored ports > Priority > System uptime > FortiGate serial number
- C. Connected monitored ports > Priority > HA uptime > FortiGate serial number
- D. Connected monitored ports > HA uptime > Priority > FortiGate serial number
Answer: C
Explanation:
When HA override is enabled, FortiGate uses the following election order: number of connected monitored ports, then device priority, followed by HA uptime, and finally FortiGate serial number as a tiebreaker.
NEW QUESTION # 27
An administrator suspects that the Collector Agent is not forwarding login events to FortiGate.
What is the most effective troubleshooting step?
- A. Verify if DC agent is enabled on the FortiGate.
- B. Verify if FortiGate is set to use LDAP authentication instead of FSSO.
- C. Check if TCP port 8000 is open between the collector agent and FortiGate.
- D. Restart the domain controller to refresh authentication services.
Answer: C
Explanation:
The Collector Agent communicates with FortiGate over TCP port 8000. Ensuring this port is open and reachable is essential for forwarding login events.
NEW QUESTION # 28
Which three statements explain a flow-based antivirus profile? (Choose three.)
- A. Flow-based inspection uses a hybrid of the scanning modes available in proxy-based inspection.
- B. Flow-based inspection optimizes performance compared to proxy-based inspection.
- C. If a virus is detected, the last packet is delivered to the client.
- D. The IPS engine handles the process as a standalone.
- E. FortiGate buffers the whole file but transmits to the client at the same time.
Answer: A,B,E
Explanation:
Flow-based antivirus buffers the entire file while simultaneously transmitting data to the client to minimize latency.
Flow-based inspection combines multiple scanning techniques from proxy-based modes for efficient detection.
Flow-based inspection provides better performance by processing traffic on the fly without full proxy overhead.
NEW QUESTION # 29
A remote user reports slow SSL VPN performance and frequent disconnections. The user is located in an area with poor internet connectivity.
What setting should the administrator adjust to improve the user's experience?
- A. Change the SSL VPN port to a non-standard port.
- B. Configure the DTLS timeout to accommodate high-latency connections.
- C. Enable split tunneling to reduce VPN traffic.
- D. Increase the session timeout for inactive sessions.
Answer: B
Explanation:
Adjusting the DTLS timeout helps maintain SSL VPN stability and performance in environments with poor or high-latency internet connectivity by allowing more time for packet retransmissions before dropping the connection.
NEW QUESTION # 30
Refer to the exhibit.
As an administrator you have created an IPS profile, but it is not performing as expected. While testing you got the output as shown in the exhibit.
What could be the possible reason of the diagnose output shown in the exhibit?
- A. Administrator entered the command diagnose test application ipsmonitor 99.
- B. Administrator entered the command diagnose test application ipsmonitor 5.
- C. FortiGate entered into IPS fail open state.
- D. There is a no firewall policy configured with an IPS security profile.
Answer: D
Explanation:
The output shows the IPS engine count as 0, indicating no active IPS engines are running. This typically means no firewall policy is referencing the IPS security profile, so the IPS profile is not being applied or triggered.
NEW QUESTION # 31
Refer to the exhibit, which shows a partial configuration from the remote authentication server.
Why does the FortiGate administrator need this configuration?
- A. To authenticate and match the Training OU on the RADIUS server.
- B. To authenticate only the Training user group.
- C. To set up a RADIUS server Secret.
- D. To authenticate Any FortiGate user groups.
Answer: B
Explanation:
The Fortinet-Group-Name attribute is used to restrict authentication to users who belong specifically to the "Training" user group on the RADIUS server.
NEW QUESTION # 32
......
Fortinet FCP_FGT_AD-7.6 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
FCP_FGT_AD-7.6 Questions PDF [2025] Use Valid New dump to Clear Exam: https://pass4sure.testvalid.com/FCP_FGT_AD-7.6-valid-exam-test.html