100% Pass Your JN0-362 Exam Dumps at First Attempt with TestValid
Penetration testers simulate JN0-362 exam PDF
NEW QUESTION 40
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The configuration is for an external BGP session
- B. The local-address statement is required for the BGP session to establish correctly
- C. The configuration is for an internal BGP session
- D. The multi-hop statement is required for the BGP session to establish correctly
Answer: B,C
NEW QUESTION 41
Which forwarding table designation is used to indicate that load balancing is working correctly?
- A. msct
- B. ucst
- C. mlst
- D. ulst
Answer: D
NEW QUESTION 42
Click the Exhibit.
Referring to the configuration in the exhibit, which statement is true?
- A. The next-hop 172.16.1.2 must be active in route table inet.3 for the route 192.168.5.0/24 to be active.
- B. The next-hop 172.16.1.2 must respond to ping commands for the route 192.168.5.0/24 to be active.
- C. The next-hop 172.16.1.2 must be part of an active route in route table inet.0 for route
192.168.5.0/24 to be active. - D. The next-hop 172.16.1.2 must be directly connected to the router for route 192.168.5.0/24 to be active.
Answer: C
NEW QUESTION 43
To which multicast address is a VRRP advertisement packet sent?
- A. 224.0.0.13
- B. 224.0.0.22
- C. 224.0.0.18
- D. 224.0.0.6
Answer: C
NEW QUESTION 44
You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Layer 2 VPN technology should you propose?
- A. BGP Layer 2 VPN
- B. BGP-signaled VPLS, using the RFC 4448 Layer 2 frame format
- C. LDP-signaled VPLS
- D. LDP Layer 2 circuit, using the RFC 4448 Layer 2 frame format
Answer: B
NEW QUESTION 45
Click the Exhibit button.
Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?
- A. the loopback address
- B. the multicast address
- C. the link-local address
- D. the statically assigned address
Answer: C
NEW QUESTION 46
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The BGP peering between R1 and R4 should use physical interface addresses
- B. The BGP peerings between R1, R2, and R3 should use loopback interface addresses
- C. The BGP peerings between R1, R2, and R3 should use physical interface addresses
- D. The BGP peering between R1 and R4 should use loopback interface addresses
Answer: A,B
NEW QUESTION 47
You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisition.Which statement is correct about this scenario?
- A. Type 5 LSAs would be converted to type 7 LSAs.
- B. Type 5 LSAs would be blocked in a stub area.
- C. Type 5 LSAs would carry external information across your transit area to the backbone.
- D. Type 5 LSAs would be seen only in the newly attached area.
Answer: B
NEW QUESTION 48
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. Interface xe-0/0/0.0 can only form a single adjacency
- B. Interface ge-1/0/0.0 can only form a single adjacency
- C. Interface xe-0/0/0.0 has a default metric of 10
- D. Interface ge-3/0/0.0 has a default metric of 10
Answer: B
NEW QUESTION 49
Click the Exhibit button.
You configured R1 and R2 to form an OSPF adjacency, but the adjacency will not establish. Referring to the exhibit, which statement correctly identifies the problem?
- A. R2 has a wrong area configured
- B. R1 does not have a router ID defined
- C. R1 and R2 have the same router ID
- D. Hello and dead timers are not matching between R1 and R2
Answer: C
NEW QUESTION 50
What is the size of the unique address used to identify each node on an Ethernet LAN?
- A. 6 bytes
- B. 12 bytes
- C. 3 bytes
- D. 9 bytes
Answer: A
NEW QUESTION 51
You have just configured IPv6 in your network. A packet arrives on your router that exceeds the MTU size. How will an IPv6 router respond?
- A. The packet is dropped.
- B. The fragment offset is referenced and the packet is fragmented.
- C. The packet is kept intact and not fragmented.
- D. The packet is fragmented based on extension headers.
Answer: A
NEW QUESTION 52
In a stateless IPv6 auto-configuration scenario, what is the host's IPv6 address if the interface's MAC address is 12:34:ab:cd:ef:56?
- A. fec0::1234:abff:fecd:ef56/64
- B. fe80::1234:abff:fecd:ef56/64
- C. fe80::1234:abcd:ef56/64
- D. fe8::1234:abff:fecd:ef56/64
Answer: C
NEW QUESTION 53
Click the Exhibit.
You have just configured a GRE tunnel, but you notice that the GRE tunnel is flapping.
Referring to the exhibit, which two would you take to solve this problem? (Choose two.)
- A. Add a specific static route to the local peer's network with the remote devices'loopback address as the next-hop gateway.
- B. Add a specific route to the remote device's loopback address with the next-hop device defined as the next-hop gateway.
- C. Remove the existing 192.168.2.0/30 static route.
- D. Set the GRE interface with a larger TTL value.
Answer: B,C
NEW QUESTION 54
What are two methods for decreasing the size of an OSPF link-state database (LSDB)? (Choose two.)
- A. Change a stub area to NSSA when possible.
- B. Ensure that all routers on a shared segment are configured with a priority value of 0.
- C. Use an interface type of p2p when possible.
- D. Segment large groups of routers into areas.
Answer: C,D
NEW QUESTION 55
You are asked to change the default TTL handling behavior on your Junos device to ensure that the RSVP- signaled LSPs in your MPLS network cannot be mapped.
Which configuration should be performed to accomplish this task?
- A. Configure the no-decrement-ttl parameter for each LSP on the ingress device
- B. Configure the no-propagate-ttl parameter for each LSP on the egress device
- C. Configure the no-decrement-ttl parameter for each LSP on the egress device
- D. Configure the no-propagate-ttl parameter for each LSP on the ingress device
Answer: B
NEW QUESTION 56
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. R2 will be the designated router
- B. R1 will not participate in the election process
- C. R4 will be the designated router
- D. R3 will not participate in the election process
Answer: D
NEW QUESTION 57
Which RSVP object allows LSRs to influence path selection?
- A. session object
- B. explicit route object
- C. record route object
- D. hop object
Answer: A
NEW QUESTION 58
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The configuration is for an external BGP session
- B. The local-address statement is required for the BGP session to establish correctly
- C. The configuration is for an internal BGP session
- D. The local-address statement is not required for the BGP session to establish correctly
Answer: B,C
NEW QUESTION 59
What is required on the egress and ingress devices to transport IPv6 traffic across an IPv4 network?
- A. A GRE tunnel interface
- B. An IP-IP interface
- C. A TE tunnel interface
- D. A 6to 4 tunnel interface
Answer: A
NEW QUESTION 60
You want to disable MAC learning only for interface ge-0/0/0.0 on an MX Series device.
Which syntax will accomplish this task?
- A. Option C
- B. Option D
- C. Option B
- D. Option A
Answer: A
NEW QUESTION 61
Click the Exhibit button.
You are troubleshooting a new BGP peering session which is not establishing. Referring to the exhibit, which statement is true?
- A. The peer's AS number is misconfigured
- B. The TCP session is not establishing
- C. The neighbor does not support IPv6
- D. The update messages contain an unsupported option
Answer: A
NEW QUESTION 62
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The OSPF neighbor will be declared down if BFD hello packets are not received for 5 seconds
- B. The OSPF neighbor will be declared down if three BFD hello packets are missed
- C. The OSPF neighbor will be declared down if BFD hello packets are not received for 1.5 seconds
- D. The OSPF neighbor will be declared down if 500 BFD hello packets are missed
Answer: B,C
NEW QUESTION 63
Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router.
What is the result of applying this policy?
- A. The 172.18.1.0/32 network will be redistributed into OSPF as an internal route.
- B. The 172.18.1.0/24 network will be redistributed into OSPF as an external route.
- C. The 172.18.1.0/24 network will be redistributed into OSPF as an internal route.
- D. The 172.18.1.0/32 network will be redistributed into OSPF as an external route.
Answer: B
NEW QUESTION 64
......
All JN0-362 Dumps and Training Courses: https://pass4sure.testvalid.com/JN0-362-valid-exam-test.html